GitBucket
4.21.2
Toggle navigation
Snippets
Sign in
Files
Branches
1
Releases
Issues
Pull requests
Labels
Priorities
Milestones
Wiki
Forks
mark.george
/
Wiki
Compare Revisions
View Page
Back to Page History
Vim.md
### Reuse last selection ``` gv ``` ### Jump to last edit There are a few ways to do this (and I can never remember a single freaking one of them). The best option is to use the changes history: View the change history: ``` :changes ``` The current position is the history is marked by a `>` Jump back in the history: ``` g; ``` Jump forward: ``` g, ``` ### Multi-select cut/paste This appends the copied selection into a register, so first clear the register using `qaq` (for the `a` register - use `qbq` for `b`, etc). This records an empty macro into the register, so you will see messages relating to macros in the status line. Multi-select yank using `:g/<search term>/y A` Multi-select delete using `:g/<search term>/d A` Multi-select move using `:g/<search term>/m <line to move to>` Also see: https://vim.fandom.com/wiki/Power_of_g `A` is the `a` register, but the uppercase variant causes the command to append to the register. If you didn't append then you will only end up with the last selection in the register. Paste using `"ap` where `a` is the register. You can view the currently used registers with `:registers` (shorthand `:reg`) ### Clearing registers The registers can fill up with crap over time if you have persistence turned on. You can clear out all the registers using the following command: ``` let regs=split('abcdefghijklmnopqrstuvwxyzABCDEFGHIJKLMNOPQRSTUVWXYZ0123456789/-"', '\zs') | for r in regs | call setreg(r, []) | endfor | unlet regs ``` ### Spell Checking Turn on spell checking (I usually have it off by default) ``` set spell ``` * Navigate errors with `]s` and `[s`. * Show replacements with `z=`. I also have Telescope configure to do that with `<leader>fs`. * Use `:spellrepall` to repeat a replacement throughout the document. * Add word to temporary ignore list `zG` * Add a word to spellfile `zg` (permanent ignore).
### Reuse last selection ``` gv ``` ### Jump to last edit There are a few ways to do this (and I can never remember a single freaking one of them). The best option is to use the changes history: View the change history: ``` :changes ``` The current position is the history is marked by a `>` Jump back in the history: ``` g; ``` Jump forward: ``` g, ``` ### Multi-select cut/paste This appends the copied selection into a register, so first clear the register using `qaq` (for the `a` register - use `qbq` for `b`, etc). This records an empty macro into the register, so you will see messages relating to macros in the status line. Multi-select yank using `:g/<search term>/y A` Multi-select delete using `:g/<search term>/d A` Multi-select move using `:g/<search term>/m <line to move to>` Also see: https://vim.fandom.com/wiki/Power_of_g `A` is the `a` register, but the uppercase variant causes the command to append to the register. If you didn't append then you will only end up with the last selection in the register. Paste using `"ap` where `a` is the register. You can view the currently used registers with `:registers` (shorthand `:reg`) ### Clearing registers The registers can fill up with crap over time if you have persistence turned on. You can clear out all the registers using the following command: ``` let regs=split('abcdefghijklmnopqrstuvwxyzABCDEFGHIJKLMNOPQRSTUVWXYZ0123456789/-"', '\zs') | for r in regs | call setreg(r, []) | endfor | unlet regs ``` ### Spell Checking Turn on spell checking (I usually have it off by default) ``` set spell ``` * Navigate errors with `]s` and `[s`. * Show suggestions with `z=`. I also have Telescope configure to do that with `<leader>fs`. * Add a word to spellfile `zg`.
GitBucket
4.21.2